Circutor OPTIM-EMS-C Series Bedienungsanleitung Seite 1

INSTRUCTION MANUAL(M057B01-03-14A)Low voltage capacitor bank with static switching operation.OPTIM EMS-C series

3.- INSTALLATION 3.1.- PRELIMINARY RECOMMENDATIONSIn order to use the unit safely, it is critical that individuals who handle it follow the saf

Do not touch the terminals or active parts of the unit until you have veried that voltage is not present. If you have to handle or touch the terminal

3.3.- INSTALLATION LOCATIONIt is important to maintain a minimum distance around the unit to facilitate cooling. As it is a wall-assembled cabi

3.4.-CONNECTION OF THE CAPACITOR BANK TO THE MAINSCheck that the rated voltage of the capacitor bank matches the voltage between phases of the

3.6.- EXTERNAL ISOLATION AND PROTECTION ELEMENTSThe capacitor bank has a manual internal four-pole isolator, but it must be connected to a line

3.9.- CURRENT TRANSFORMER (CT) CONNECTION A current transformer (CT) outside the capacitor bank must be installed to measure the total load cur

Figure 9: Current transformer (CT) connection terminals.Once the cables are installed, disconnect the jumper connecting the S1 and S2 terminals of the

4.- STATIC CAPACITOR BANK START-UP 4.1.- BEFORE START-UPThe static capacitor banks include a power factor regulator. Prior to start-up, the ope

2.- Connect the power supply to the panel and check that the regulator display illuminates im-mediately. Otherwise, stop and check the previous step.3

4.3.- CHECKS AFTER THE CAPACITOR BANK IS CONNECTED AND THE REGULATOR ADJUSTED1.- After start-up, make sure that the unit is operating correctly

2OPTIM EMS-C series Instruction Manual

5.- MAINTENANCE 5.1.- SAFETY REGULATIONSTake the safety regulations listed in section of this manual into account before operating the units “

5.2.2. TIGHTENING TORQUE OF THE ELECTRICAL CONNECTIONSThe connections must be tight.The tightening torques for the fuse bases are indicated in Table 2

5.2.6. CLEANING THE CABINET Remove any solid particles. Clean the inside of the cabinet. Clean ventilation grilles. 5.3.- MAINTENANCE WITH TH

5.3.1. REGULATOR CHECKSSee the specic regulator manual or quick guide used for the capacitor bank. The manual or quick guide is always provided with

6.- TECHNICAL FEATURESElectrical featuresWorking voltage and nominal frequency Un / fn, listed on the labelDesign voltage Un+ 10% (440 V for 400V uni

7.- OPTIM EMS-C TYPE DIAGRAMDENOMINACIONFECHAUNIDAD DIMESCALAAPROBADODIBUJADONOMBRESUSTITUIDO PORSUSTITUYE ACODIGOEQUIPO/S07/10/201407/10/2014L1L2L3

8.- MAINTENANCE AND TECHNICAL SERVICE 9.- GUARANTEE• No returns will be accepted and no unit will be repaired or replaced if it is not ac-companied b

10.- CE CERTIFICATE27Instruction ManualOPTIM EMS-C series

CIRCUTOR, SA Vial Sant Jordi, s/n08232 -Viladecavalls (Barcelona)Tel.: (+34) 93 745 29 00 - Fax: (+34) 93 745 29 14 www.circutor.es central@circutor

SAFETY PRECAUTIONS DISCLAIMERCIRCUTOR, SA reserves the right to make modi cations to the device or the unit speci ca-tions set out in this instruct

CONTENTSSAFETY PRECAUTIONS ...

REVISION LOGTable 1: Revision log.Date Revision Description10/14 M057B01-03-14A Initial VersionNote: The images of the units are solely for the purpo

1.- VERIFICATION UPON RECEPTION 1.1.- RECEPTION PROTOCOLCheck the following points when you receive the unit: a) The unit meets the specicati

When unloading and moving the unit, use a forklift with forks long enough to support the entire length of the base. Otherwise, the forks should be lon

2.- PRODUCT DESCRIPTIONThe purpose of this manual is to assist during the installation, start-up and maintenance of OPTIM EM-C series l

Th-D 1QTh-D 2PPPC1PPPC2U2 V2 W21 3 52 4 6U1U213245RadiadorV1V213245PLACA1G1+-CPC4CONTROL1K1PLACA1G1+-CPC4CONTROL1K112VDC12VDCMandoAlimentación Potenci